Products

• basic design Ø8mm, -25…+200°C (T=c. 10sec) or –25…+400°C (T=c. 25sec)
• screw fitting: M12x1,5 M12x1,75; G1/4, G1/2; M20x1,5; M27x2, G3/4 or others by request
• stem from stainless steel Ø8 or 10mm
  • it can be use transmitters
       - PP200 with output 4…20mA
       - PP300 with output 0…10V
       - PX300 with output 4…20mA with galvanic isolation
•    - PPL100 with output ASCII or MODBUS
• power supply by output loop 8…28V DC, ripple max. 0,5V
• any measuring range <-50…+80>°C, min. span 50°C
• accuracy ±0,5% from span (max. ±0,25°C)
• another parameters are shown in the datasheet of used transmitter

• basic design: stem Ø8mm, thermowell Ø10mm or stem Ø6mm, thermowell Ø10mm
• measuring range-25…+200°C (T=c. 30sec) or –25…+400°C (T=c. 50sec)
• screw fitting: G1/2; M20x1,5; M27x2, G3/4..
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• accuracy according to used sensor

• basic design: stem Ø8mm, thermowell Ø10mm or stem Ø6mm, thermowell Ø10mm
• measuring range-25…+200°C (T=c. 30sec) or –25…+400°C (T=c. 50sec)
• screw fitting: G1/2; M20x1,5; M27x2, G3/4..
• it can be use transmitters
     - PP200 with output 4…20mA
     - PP300 with output 0…10V
     - PX300 with output 4…20mA with galvanic isolation
     - PPL100 with output ASCII or MODBUS
• power supply by output loop 8…28V DC, ripple max. 0,5V
• any measuring range <-50…+80>°C, min. span 50°C
• accuracy ±0,5% from span (max. ±0,25°C)
• another parameters are shown in the datasheet of used transmitter

• basic design Ø6mm, -25…+200°C (T=c. 10sec) or –25…+400°C (T=c. 25sec)
• screw fitting: M12x1,5 M12x1,75; G1/4, G1/2; M20x1,5; M27x2, G3/4..
• stem from stainless steel Ø 3, 4, 5 or 6mm
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• accuracy according to used sensor

• basic design Ø6mm, -25…+200°C (T=c. 10sec) or –25…+400°C (T=c. 25sec)
• screw fitting: M12x1,5 M12x1,75; G1/4, G1/2; M20x1,5; M27x2, G3/4..
• stem from stainless steel Ø 3, 4, 5 or 6mm
• it can be use transmitters
     - PP200 with output 4…20mA
     - PP300 with output 0…10V  
     - PX300 with output 4…20mA with galvanic isolation
     - PPL100 with output ASCII or MODBUS
• power supply by output loop 8…28V DC, ripple max. 0,5V
• any measuring range <-50…+80>°C, min. span 50°C
• accuracy ±0,5% from span (max. ±0,25°C)
• another parameters are shown in the datasheet of used transmitter

• basic design Ø8mm, -25…+200°C (T=c. 10sec) or –25…+400°C (T=c. 25sec)
• stem from stainless steel Ø 3, 4, 5, 6, 8 or 10mm
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• accuracy according to used sensor

• basic design Ø6mm, -25…+200°C (T=c. 10sec) or –25…+400°C (T=c. 25sec)
• screw fitting: M12x1,5 M12x1,75; G1/4, G1/2; M20x1,5; M27x2, G3/4..
• stem from stainless steel Ø 3, 4, 5 or 6mm
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• accuracy according to used sensor

• basic design Ø6mm, -25…+200°C (T=c. 10sec) or –25…+400°C (T=c. 25sec)
• screw fitting: M12x1,5 M12x1,75; G1/4, G1/2; M20x1,5; M27x2, G3/4..
• stem from stainless steel Ø 3, 4, 5 or 6mm
• inbuilt programmable transmitter PMA300 with 4…20mA output
• power supply by output loop 8…30V DC, ripple max. 0,5V
• any measuring range <-50…+80>°C, min. span 50°C
• accuracy ±0,5% from span (max. ±0,25°C)
• another parameters are shown in the datasheet of used transmitter PMA300

The power supplies are intended to power the converters, isolating modules, converter stem thermometers and other devices in the industry. They are mounted into switchboxes on a DIN 35 standard electrical equipment mounting rail.

• supply voltage: 230V AC ± 10% (45 – 65 Hz)
• output voltage: 24V DC, ±5%
• output power capacity: 0.5VA (22mA)
• protection: transformer with thermal fuse + electronic cut-out

The power supplies are intended to power the converters, isolating modules, converter stem thermometers and other devices in the industry. They are mounted into switchboxes on a DIN 35 standard electrical equipment mounting rail.

• supply voltage: 230V AC ± 10% (45 – 65 Hz)
• output voltage: 24V DC, ±5%
• output power capacity: 5VA (200mA)
• protection: transformer with resettable thermal fuse

• measurement frequency in wide range 0..120kHz
• unipolar and bipolar input signl
• conversion accuracy  0,2%
• response time 300ms
• isolation input-output-power supply: 4000Vef
• universal power supply 19 – 300V DC & 90 – 250V AC

• PID / 2-state controller
• controlling of stp value
• 1 measuring input
• 2 outputs
• communication line
• ramp function
• automatic / manual operation

• 3 initial configurations of device:
  • meter / alarm unit
  • two-state controller
  • PID controller
• 1 measuring input
• 2 outputs
• communication lines

• 1 measuring inputs
• 3 outputs
• communication line
• simple program (ramp up, soak)
• option for the delayed start of the program
• start of the program with the key
• easy operation

• 1 measurement input
• three control outputs
• communication line
• simple program (2 x ramp-up, 2 x soak)
• possibility of delay in starting the program
• running a program using the keyboard
• simple operation

• low voltage current transformers
• using in low voltage switchboards up to 2500A
• certified calibration
• customized on request

Continue HERE in new window please
(Czech language only)

• controlling the power element by pulse width modulation (PWM)
• PWM output 0..12V / 25mA
• selectable frequency of output pulses 1Hz, 10Hz, 100Hz or 1kHz
• PWM controlled by voltage, current or potentiometer 1 to 10kOhm
• auxiliary power supply 19-300V DC 90-250V AC
• conversion accuracy <0.2%
• separation input - output - power 4000Vef
• the converter's user configuration
• small size
• DIN rail mounting 35

• sensor is built-in to plastic box, wall mounting design
• sensor 1x Pt100A, B, Pt1000, Ni1000 or others
• accuracy according to used sensor

• sensor is built-in to plastic box, wall mounting design
• connecting by three wires (GND, OUT, +Ucc)
• power supply 12…34V DC
• voltage ripple max. 0,5V
• measuring range 0…+50°C (or others)
• output 0…5V
• accuracy +/- 0,3°C

• connector M12x1 EC-FS4-L/16
• diameter 5 to 8mm (or others), fitting length „Y“ according to order
• purpose: to sink intro the lock fitting bracket or air conditioning
• basic design: 8x100mm Pt100/B G1/2 2w max. 100°C
• temperature range: -30…+100° (T=c. 7sec)
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• accuracy according to used sensor
• metal parts are made from stainless steel 17248
• enclosure IP code: IP65
• dielectric strength: 500V, insulation resistance min. 20MΩ (circuit to metal parts)